[ < ] [ Up ] [ > ]               [Top] [Contents] [Index] [ ? ]

8.3 Vertex Animation

Vertex animation is about using information about the movement of vertices directly to animate the mesh. Each track in a vertex animation targets a single VertexData instance. Vertex animation is stored inside the .mesh file since it is tightly linked to the vertex structure of the mesh.

There are actually two subtypes of vertex animation, for reasons which will be discussed in a moment.

8.3.1 Morph Animation
Morph animation is a very simple technique which interpolates mesh snapshots along a keyframe timeline. Morph animation has a direct correlation to old-skool character animation techniques used before skeletal animation was widely used.
8.3.2 Pose Animation
Pose animation is about blending multiple discrete poses, expressed as offsets to the base vertex data, with different weights to provide a final result. Pose animation's most obvious use is facial animation.

Why two subtypes?

So, why two subtypes of vertex animation? Couldn't both be implemented using the same system? The short answer is yes; in fact you can implement both types using pose animation. But for very good reasons we decided to allow morph animation to be specified separately since the subset of features that it uses is both easier to define and has lower requirements on hardware shaders, if animation is implemented through them. If you don't care about the reasons why these are implemented differently, you can skip to the next part.

Morph animation is a simple approach where we have a whole series of snapshots of vertex data which must be interpolated, e.g. a running animation implemented as morph targets. Because this is based on simple snapshots, it's quite fast to use when animating an entire mesh because it's a simple linear change between keyframes. However, this simplistic approach does not support blending between multiple morph animations. If you need animation blending, you are advised to use skeletal animation for full-mesh animation, and pose animation for animation of subsets of meshes or where skeletal animation doesn't fit - for example facial animation. For animating in a vertex shader, morph animation is quite simple and just requires the 2 vertex buffers (one the original position buffer) of absolute position data, and an interpolation factor. Each track in a morph animation refrences a unique set of vertex data.

Pose animation is more complex. Like morph animation each track references a single unique set of vertex data, but unlike morph animation, each keyframe references 1 or more 'poses', each with an influence level. A pose is a series of offsets to the base vertex data, and may be sparse - ie it may not reference every vertex. Because they're offsets, they can be blended - both within a track and between animations. This set of features is very well suited to facial animation.

For example, let's say you modelled a face (one set of vertex data), and defined a set of poses which represented the various phonetic positions of the face. You could then define an animation called 'SayHello', containinga single track which referenced the face vertex data, and which included a series of keyframes, each of which referenced one or more of the facial positions at different influence levels - the combination of which over time made the face form the shapes required to say the word 'hello'. Since the poses are only stored once, but can be referenced may times in many animations, this is a very powerful way to build up a speech system.

The downside of pose animation is that it can be more difficult to set up, requiring poses to be separately defined and then referenced in the keyframes. Also, since it uses more buffers (one for the base data, and one for each active pose), if you're animating in hardware using vertex shaders you need to keep an eye on how many poses you're blending at once. You define a maximum supported number in your vertex program definition, via the includes_pose_animation material script entry, See section Pose Animation in Vertex Programs.

So, by partitioning the vertex animation approaches into 2, we keep the simple morph technique easy to use, whilst still allowing all the powerful techniques to be used. Note that morph animation cannot be blended with other types of vertex animation on the same vertex data (pose animation or other morph animation); pose animation can be blended with other pose animation though, and both types can be combined with skeletal animation. This combination limitation applies per set of vertex data though, not globally across the mesh (see below). Also note that all morph animation can be expressed (in a more complex fashion) as pose animation, but not vice versa.

Subtype applies per track

It's important to note that the subtype in question is held at a track level, not at the animation or mesh level. Since tracks map onto VertexData instances, this means that if your mesh is split into SubMeshes, each with their own dedicated geometry, you can have one SubMesh animated using pose animation, and others animated with morph animation (or not vertex animated at all).

For example, a common set-up for a complex character which needs both skeletal and facial animation might be to split the head into a separate SubMesh with its own geometry, then apply skeletal animation to both submeshes, and pose animation to just the head.

To see how to apply vertex animation, See section 8.2 Animation State.


[ < ] [ Up ] [ > ]               [Top] [Contents] [Index] [ ? ]

This document was generated by Steve Streeting on , 12 2006 using texi2html